G R A N D
T O U R IN G
S E R IE S
®
G T O 1 7 T
t w e e t e r
o w n e r ’s
m a n u a l
T H A N K Y O U
for purchasing a JBL GTO17T automotive
®
tweeter. We’ve organized this manual to make
your installation as simple and trouble-free
as possible. Please read it thoroughly before
proceeding. Remember to keep your sales
receipt and this manual in a safe place so
both are available for future reference.
T W E E T E R IN S T A LLA T IO N
S UR FA C E-M O UN T
Figure 4. Surface-mounting the tweeter
and connecting the crossover.
Figures 7A through 7D. The Starfish™
tweeter mount is intended to be used
when the tweeter will be installed behind a
factory grille (e.g., replacing the factory
tweeter behind a door panel). The Starfish
will allow you to mount the component
tweeter directly to the panel itself or to the
area behind the panel. The six mounting
tabs can be removed easily to create a
number of custom configurations.
Figure 7B. Flush-mounted to surface
behind grille panel.
BLACK (–)
(–) SMALL LUG
BLACK
RED (+)
BLACK (–)
RED (+)
RED
1
(+) LARGE LUG
Note: Check screw clearance before
2
installing. Use glue if clearance is an issue.
Figure 7C. Mounted to grille panel.
Note: Not all possible mounting
configurations are shown.
TW EETER A N G LE
Figure 6. Aim the tweeter at the listening
position by sliding the screw in the groove
on the back of the tweeter cup and lock
the tweeter in place using the small retain-
ing screw. Rotate the entire assembly in
the mounting surface and tighten the large
hand nut.
Figure 7A. Surface-mounted behind grille
panel.
FLUS H-M O UN T
Figure 5. Mounting the tweeter using
the I-Mount™ (patent no. 5,859,917)
flush-mounting kit.
3
3
ROTATE ENTIRE ASSEMBLY
TO AIM ANGLED TWEETER
TOWARD LISTENER.
Figure 7D. In-dash location (may require
gluing).
1
1
SLIDE SCREW UP OR
DOWN TO ADJUST
TWEETER ANGLE.
2
2
TIGHTEN SCREW TO
LOCK ANGLE SETTINGS.
4
SECURELY TIGHTEN
THE LARGE HAND NUT.
3
S P E C IF IC A T IO N S
GTO17T
1" Tweeter
50W*
Power Handling, RMS
Power Handling, Peak
Sensitivity (2.83V/1m)
Frequency Response
Impedance
150W*
92dB
2.5kHz – 21kHz
2 Ohms
Mounting Depth
3/4" (19mm)
1-7/8" (48mm)
Cutout Diameter
* With enclosed filter
General Care
The loudspeaker grilles may be cleaned with a damp cloth. Do not use any cleaners or solvents on the grilles or the speaker cones.
A valid serial number is required for warranty coverage.
Features, specifications and appearance are subject to change without notice.
Declaration of Conformity
JBL Consumer Products
250 Crossways Park Drive, Woodbury, NY 11797 USA
We, Harman Consumer Group International
2, route de Tours
© 2005 Harman International Industries, Incorporated. All rights reserved.
72500 Château du Loir
France
JBL, Harman International and Grand Touring Series are trademarks
declare in own responsibility that the product described in this owner’s manual is in
compliance with technical standards:
of Harman International Industries, Incorporated, registered in the
United States and/or other countries. I-Mount and Starfish are
trademarks of Harman International Industries, Incorporated.
EN 61000-6-3:2001
EN 61000-6-1:2001
Klaus Lebherz
Harman Consumer Group International
Château du Loir, France 11/05
Part No. GTO17TOM11/05
w w w . j b l . c o m
|