COMPONENT
#691170
14.4V BATTERY-OPERATED DRILL
INSTRUCTION MANUAL
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO
SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE
DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION
AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE
A SUGGESTION OR COMMENT, GIVE US A CALL OR EMAIL US AT: INFO@ALLTRADETOOLS.COM.
YOUR FEEDBACK IS VITAL TO US.
PARA EL SERVICIO
PARA EL CONSUMIDOR
87-1904-60957
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™ MOTORS CORP.,
U.S.A., WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT.
CONSUMER INQUIRES SHOULD BE DIRECTED TO:
1-800-590-3723
©COPYRIGHT 2006 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
Printed in China
Imprimé dans la Chine
Impreso en China
LONG BEACH, CA 90810-1462 USA
691170 – 14.4V Black Cordless Drill_Rev 11/21/06
WORK AREA
DANGER
indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
Keep your work area clean and well lit.
areas may cause accidents or injury.
Cluttered work benches and dark work
WARNING
indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
Do not operate power tools in explosive areas, such as in the presence of
flammable liquids, gases or dust.
the dust or fumes.
Power tools create sparks which may ignite
CAUTION
indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose control.
CAUTION
used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
ELECTRICAL SAFETY
NOTE
provides additional information that is useful
Do not abuse the cord. Never use the cord to carry the tool. Keep the cord
away from heat, oil, sharp edges, or moving parts. Replace damaged cords
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
immediately.
Damaged cords may create a fire.
A battery operated tool with integral batteries or a separate battery pack
must be recharged only with the specified charger for the battery.
IMPORTANT SAFEGUARDS
A charger
that may be suitable for one type of battery may create a risk of fire when used with
another battery.
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
Use battery operated tool only with specifically designated battery pack.
any other batteries may create risk of fire.
Use of
WARNING:
Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
WARNING:
Handling the power cord on corded products may expose you to
lead, a chemical known to the State of California to cause cancer and birth
Wash hands after handling.
defects or other reproductive harm.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
4
PERSONAL SAFETY
When battery pack is not in use, keep it away from other metal objects like:
paper clips, coins, keys, nails, screws, or other small metal objects that can
Stay alert, watch what you are doing, and use common sense when operat-
ing a power tool. Do not use tool while tired or under the influence of drugs,
make a connection from one terminal to another.
nals together may cause sparks, burns or a fire.
Shorting the battery termi-
alcohol or medication.
A moment of inattention while operating power tools
Maintain tools with care. Keep cutting tools sharp and clean
. Properly maintained
may result in serious personal injury.
tools with sharp cutting edge are less likely to bind and are easier to control.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts.
jewelry or long hair can be caught in moving parts.
Loose clothes,
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using.
Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the manufacturer for your
model.
Avoid accidental starting. Be sure switch is in the locked or “OFF” position
before inserting battery pack.
Carrying power tools with your finger on the
“ON”
switch or inserting battery pack into a tool with the power switch
accidents.
invites
Accessories that may be suitable for one tool may create a risk of injury
when used on another tool.
Remove adjusting keys or wrenches before turning the tool “ON”.
A wrench
SERVICE
or a key that is left attached to a rotating part of the tool may result in person-
al injury.
Tool service must be performed only by qualified repair personnel.
maintenance by unqualified personnel may result in a risk of injury.
Service or
Do not overreach. Keep proper footing and balance at all times.
Proper foot-
ing and balance enable better control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection.
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance section of this manual.
Dust mask, non-skid safe-
Use of unauthorized parts or failure to
ty shoes, hard hat, or hearing protection must be used for appropriate conditions.
follow Maintenance Instructions may create a risk of shock or injury.
TOOL USE AND CARE
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Hold tool by insulated gripping surfaces when perform-
Use clamps or other practical ways to secure and support the workpiece to a
ing an operation where the cutting tool may contact hidden wiring.
Contact
stable platform.
Holding the work by hand or against your body is unstable and
with a “live” wire will also make exposed metal parts of the tool “live” and shock
the operator.
may lead to loss of control.
Do not force tool. Use the correct tool for your application.
The correct tool
will do the job better and safer at the rate for which it is designed.
SAFETY RULES FOR CORDLESS DRILL / DRIVERS
Do not use the tool if the power switch does not turn it “ON” or “OFF”.
cannot be controlled with the switch is dangerous and must be repaired.
A tool that
Always wear safety goggles or eye protection when using this tool. Use a
dust mask or respirator for applications which generate dust.
Disconnect battery pack from tool or place the switch in the locked or “OFF” posi-
tion before making any adjustments, changing accessories, or storing the tool.
Such preventative safety measures reduce the risk of starting the tool accidentally.
Do not grasp the tool or place your hands too close to the spinning chuck or
drill bit.
Your hand may be lacerated or may cause injury.
Store idle tools out of reach of children and other untrained persons.
are dangerous in the hands of untrained users.
Tools
Secure the material being worked on. Never hold it in your hand or across
your legs.
Unstable support can cause loss of control and injury.
5
6
SYMBOLS
IMPORTANT:
Some of the following symbols may be used on your tool. Please
Position yourself to avoid being caught between the tool or side handle and
walls or posts.
tion torque of the tool could crush your hand or leg.
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
Should the socket or bit become bound in the work, the reac-
Check to see that keys and adjusting wrenches are removed from the
SYMBOL
NAME
EXPLANATION
Voltage (Potential)
Current
Frequency (Cycles per Second)
Power
Weight
Type of Current
Type of Current
Cordless Drill before switching the tool “ON”.
at high velocity striking you or a bystander.
Keys or wrenches can fly away
V
A
Hz
W
Kg
Volts
Amperes
Hertz
When using the Cordless Drill, always maintain a firm grip on the tool with
both hands.
Watt
Hold tool by insulated gripping surfaces when performing an operation
Kilograms
Alternating Current
Direct Current
where the cutting tool may contact hidden wiring.
Contact with a "live" wire
will also make exposed metal parts of the tool "live" and shock the operator.
Keep the handle of the Cordless Drill dry, clean, and free from oil and
grease.
Alternating or Direct Current Type of Current
Earthing Terminal
Class II Construction
Minutes
Seconds
Diameter
Grounding Terminal
Denotes Double Insulation
Time
Time
Size of Drill Bits,
Grinding Wheels, etc.
No-load Rotational Speed
Revolutions, Surface Speed,
Strokes, etc. per Minute
Speed, Torque or Position Settings
Do not run the Cordless Drill while carrying it at your side.
A spinning
socket or bit could become entangled with clothing and injury may result.
min
s
Disconnect the plug or remove the battery pack from tool and place the switch
in the locked or “OFF” position before making any assembly adjustments,
changing accessories, performing any inspection, maintenance or cleaning
procedures.
Such preventive safety measures reduce the risk of starting the
No load speed
Revolutions per Minute
tool accidentally.
.../min
Do not use the Cordless Drill if it has been damaged, left outdoors in the
rain, snow, wet or damp eenvironments, or immersed in liquid.
1,2,3, …
Ring Selector Settings
Maintain labels and nameplates on the Cordless Drill.
These carry important
information. If unreadable or missing, contact Alltrade for a replacement.
8
FUNCTIONAL DESCRIPTION
BATTERY
Before using battery pack, please read carefully all instruc-
tions and cautionary markings on battery pack, battery
charger and product using battery.
3
5
6
7
8
®
Do not incinerate the battery pack even if it is severely dam-
11
9
aged or is completely worn out.
The battery pack can explode.
Do not carry battery packs in aprons, pockets, or tool
boxes, product kit boxes, drawers, etc. with loose metal objects.
12
Battery
4
10
2
pack terminals could be short circuited causing damage to the battery pack,
severe burns or fire.
The battery pack is Nickel-Cadmium (Ni-Cad) and is considered to be a toxic
1
material by the Environmental Protection Agency.
Before disposing of dam-
aged or worn out Ni-Cad battery packs, check with your State Environmental
Protection Agency to find out about special restrictions on the disposal of these
battery packs, take them to your local recycling center for proper disposal, or
CONTROLS AND COMPONENTS:
1. Battery Pack
2. Release Buttons on Each Side
3. 120V AC Adapter
4. Charger
5. LED Charging Indicators
6. 10mm (3/8") Keyless Chuck
1-800-822-8837
call
.
8. Forward/Reversing and
Trigger Lock Lever
9. Variable Speed Controlled
Trigger Switch
10. Accessory/Bit Holder
11. Comfort Rubber Grip
The battery is not fully charged.
Before first use, the battery pack requires
8-10 hours charge time to be fully charged. Subsequent recharging needs 3-5
hours for the battery to be fully charged.
7. 24 Adjustable Torque Settings
Control Ring
Always switch to a fresh battery when tool performance begins to diminish.
Severe heat is most destructive to a battery; the more heat generated, the faster
the battery loses power. A battery that gets too hot can have a shortened life.
ACCESSORIES:
12. Double Ended Screwdriver Bits (2)
Never over-discharge a battery by using the tool even after tool performance
has decreased.
Do not attempt to discharge a tool’s battery by continuing to
pull on the tool trigger. When tool performance begins to diminish, stop the tool
and recharge the battery for optimal performance.
COMPONENT
BATTERY PACK
120V AC ADAPTER
CHARGER
MODEL NUMBER
691167
691169
691168
Charge battery pack at ambient temperatures between 50° F – 104° F.
Store tool and battery pack in locations where temperatures will not exceed
10mm (3/8") KEYLESS CHUCK 690076
120°F.
This is important to prevent serious damage to the battery cells.
The battery pack should always be recharged when the Cordless Drill begins to
run slowly.
When battery pack is not in use, keep it away from other metal objects such as
paper clips, coins, keys, nails, screws or other small mettal objects that can
make a connection from one terminal to another.
together may cause sparks, burns, or fire.
Shorting the battery terminals
9
REMOVING/ATTACHING BATTERY PACK
REMOVE BATTERY PACK:
1. Press both release buttons on either side of
the Cordless Drill to release the battery pack.
CHARGING BATTERY PACK
BATTERY PACK
CHARGE BATTERY PACK:
1. Make sure the trigger
on the Cordless Drill
“OFF”
is in the
position
120V AC
ADAPTER
2. Pull battery pack free of Cordless Drill.
and remove the battery
pack from the Cordless
Drill.
ATTACH BATTERY PACK:
1. Align the raised portion of the battery pack
with the groove in the battery compartment
of the Cordless Drill.
2. Plug 120V AC Adapter
into household outlet
LED LIGHT
2. Press the battery pack into place. Make sure
the latches are securely fastened. Do not use
the Cordless Drill if the battery pack is not
seated properly.
and into side of battery
charger. Insert battery
pack into battery charger.
When the battery is placed
in the charger, the red
BATTERY
CHARGER
RELEASE BUTTON
LED indicator light will remain on.
3. When fully charged, reattach battery pack onto Cordless Drill,
making certain latches fasten securely. Cordless Drill will not
operate properly if the battery pack is not seated properly.
CHARGER
Before using battery charger, please read carefully all
instructions and cautionary markings on battery charger, battery pack and
product using battery.
ASSEMBLY
Be aware that this tool is always in an operating condition
because it does not have to be plugged into an electrical outlet.
Always turn
“OFF”
and remove the battery pack before changing bits.
The charger will not automatically turn “OFF” when the
the switch
battery pack is fully charged.
“ON”
The charging indicator light will remain
until the charger is disconnected from the electrical outlet.
INSTALLING DRILL BIT INTO KEYLESS CHUCK
Use only the charger which accompanied your product or direct replacement as
listed in this manual.
approved chargers with your product.
Do not substitute any other charger. Use only Alltrade
WARNING
Before inserting a drill bit or other accessory,
make sure the forward/reverse
Do not disassemble charger.
“OFF”
and trigger lock lever is in the center
that may result in injury.
position to prevent accidental starts
Do not use charger if it has been damaged, left outdoors in the rain, snow, wet
or damp environments, or immersed in liquid.
Do not attempt to tighten drill bits (or any other accessory) by gripping the
The battery pack and charger heat during charging.
Place the charger on a flat,
front of the chuck and turning the tool on.
and/or damage to the chuck.
This may cause personal injury
non-flammable surface away from flammable materials with at least four inches of
clearance to allow proper air circulation around the charger and battery pack.
When removing the bit from the tool, avoid contact with skin and use proper
protective gloves when grasping the bit orr accessory.
after prolonged use.
When the battery pack requires recharging, a 3-5 hour charge allows the tool to
Accessories may be hot
operate at full power.
A charging indicator light on the charger will illuminate to
show that charging is taking place.
11
12
1. Hold the rear end of the chuck
in one hand and use the other
hand to rotate the front end in a
counterclockwise direction to
open the jaws of the chuck.
FORWARD/REVERSE AND TRIGGER LOCK LEVER
LOOSEN
TIGHTEN
Be sure the trigger is released when changing the position of the lever.
“LOCKED/OFF”
Always store the tool in the
position.
2. Insert the shank of the bit (or
other accessory) fully into the
keyless chuck, taking care to
keep the bit in the center of
the jaws of the chuck.
Always check the direction of the Cordless Drill's rotation before use.
HOLD
TO SELECT THE DIRECTIONS
OF ROTATION:
• To select forward Cordless Drill
3. Turn the front end of the chuck clockwise to hold the bit in place.
rotation, press the trigger lock
from left to right flat against the Cordless
Drill body.
4. Tighten securely by turning the front end of the chuck clockwise while holding
the rear end.
TRIGGER
LOCK
• To select reverse, press the trigger lock lever
in the opposite direction.
OPERATING THE DRILL
Never tape the trigger switch down to provide continu-
• The center position locks the tool.
ous high speed.
personal injury.
The tool may fail under such conditions causing fire or
TORQUE SETTINGS
VARIABLE SPEED TRIGGER SWITCH
To prevent damaging the tool or driving screw too deep
into work piece, release the trigger when you feel the clutch slip.
THIS TOOL IS CONTROLLED
BY A TRIGGER SWITCH:
• The speed of the Cordless Drill depends
on the amount of pressure you put on the
trigger.
THE CONTROL RING ADJUSTS THE LEVEL OF TORQUE:
• For light duty work, use lower settings.
CONTROL RING
TRIGGER
SWITCH
• For heavy duty work, use higher settings.
• The more pressure you apply, the faster
the Cordless Drill will go.
PROPER SETTING FOR DRIVING SCREWS:
1. Set the ring on the lowest
setting to begin.
• Release the pressure and the Cordless Drill
will slow down.
2. Try tightening the first screw.
If the drill drives smoothly,
proceed with the next screw.
3. If the Drill’s clutch slips,
increase the torque setting
and try again until the Drill
drives the screw without incident.
13
14
• Use a block of wood to back up work pieces that may splinter.
• Use spade bits when drilling large diameter holes in wood.
• Use HSS drill bits when drilling in metal.
SCREWDRIVING
WHEN DRIVING FASTENERS:
• Always start slowly and gradually increase the speed of the Drill.
• Release the trigger when you feel the clutch slip.
• Use masonry bits when drilling in soft masonry.
• Always keep the driver bit straight to prevent damage to the screw.
• Hold the Drill with both hands to ensure control if the bit should stick or slip.
• Use a lubricant when drilling metals other than cast iron, aluminum, copper,
and brass.
• To prevent wood from splitting, drill pilot holes into the wood before driving
in the screws.
• When drilling, start the hole slowly, allowing the bit to drill deep enough to prevent
slipping at higher speeds.
DRILLING METAL
“ ON”
“ OFF”
.
• Never try to start a stalled Drill by clicking the trigger switch
This may damage your tool.
and
WHEN DRILLING HARD METALS:
• Apply a lubricant, such as cutting oil, to the tip of the bit.
• To reduce jamming, always keep the Drill running when pulling the bit out of a
finished hole.
• Start with a small hole then enlarge to the required size. Make sure the bit is
actually cutting and not spinning in the hole as this will dull the edges of the bit.
SCREWDRIVING:
• Always use the correct type and size of screwdriver bit.
• Keep enough pressure on the bit to keep it drilling through the material.
DRILLING MASONRY
• If screws are difficult to tighten, try applying a small amount of washing liquid or
soap as a lubricant.
WHEN DRILLING MASONRY:
• Masonry can be brittle so be careful not to apply too much pressure and crack
the material.
• Always hold the tool and screwdriver bit in a straight line with the screw.
MAINTENANCE AND CLEANING
• Apply enough pressure to keep the bit cutting and not spinning in the hole as this
will dull the edges of the bit.
Always remove the battery pack before attempting
cleaning or maintenance.
• Bricks and similar soft materials will require less pressure, concrete will require
much more.
DRILLING WOOD
This Cordless Drill is lubricated before it leaves the
factory.
lubrication is required.
This lubrication should last for the life of the tool. No further
Use twist bits to drill holes in wood. Make sure the bits are sharp. Pull the bits
out of the hole frequently to clear chips from the flutes as an overburdened bit
may overheat.
Use only mild soap and a damp cloth to clean the tool.
Never let any liquid get
inside the casing. Never immerse any part of the tool in a liquid. Always keep the
ventilation openings clear.
HINTS FOR OPTIMUM USE
Always clean the battery pack using only a dry cloth. Do not use liquids.
Always unplug the charger before cleaning it.
DRILLING:
• Keep the right amount of pressure in a straight line with the drill bit. Too little and
the bit will spin without cutting, too much and the motor may stall.
Regularly clean the ventilation slots in your tool and charger using only a soft
bbrush or dry cloth.
• Just before the drill tip breaks though the other side of the work piece drill more
slowly and decrease pressure on the tool. This will prevent stalling and leave a
cleaner hole.
Never open the Cordless Drill case, battery pack or charger.
Do not attempt to
repair the Cordless Drill, battery pack or charger yourself. Opening any of these
parts will void your warranty.
15
16
PROTECTING THE ENVIRONMENT
ACCESSORIES
BATTERIES
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
Alltrade batteries can be recharged many times. At the end of their useful life,
recycle batteries with due care for our environment.
Ni-Cad and Ni-MH batteries are recyclable. Take them to your local recycling center
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
1-800-822-8837
. Collected batteries will be recycled or disposed of properly.
or call
If you must use an extension cord, be suree that the gauge is large enough to carry
the amount of current necessary for your power tool.
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table below).
If not, your tool may experi-
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
TOOL CURRENT RATING
CONDUCTOR SIZE IN A.W.G
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
AMPERE
3-6
10FT.
18
25FT.
18
18
18
16
50FT.
18
18
18
14
100FT.
18
16
14
14
-
6-8
18
Jigsaws
8-10
18
10-12
12-16
16-20
16
14
12
Circular Saws
12
12
12
Angle Grinders
12
-
Reciprocating Saws
Routers
Rotary Tools
SPECIFICATIONS
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
SPECIFICATIONS
Voltage
Speed
14.4V
0-550/min.
24+ Drill
Torque Settings
Chuck Capacity (max)
Charger Input
10mm (3/8")
120V
60Hz
Charging Time
Battery Type
Approx. 3-5 hours
Ni-Cad
17
18
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
conforming item and/or part thereof shall constitute fulfillment of all
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
2 YEAR LIMITED HOME USE WARRANTY
Express and Exclusive Limited Home Use Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ portable power tool and no one else
all parts of the product (except those parts referred to below which are specifically
excluded from such warranty (see Exclusions)) to be free from defects in materials
and workmanship for a period of two years from original date of purchase.
SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS:
Kawasaki™ portable power tool is offered as a home use tool and carries a
This
HOME
USE WARRANTY
.
This tool is made for home use in the execution of
COMMERCIAL
projects and repairs in and around the home. Use of the tool for
PURPOSES OR ON A JOBSITE
is not covered under this warranty.
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified, altered or used for any commercial purpose or on
a jobsite. This warranty does not apply to any other product and/or component
thereof manufactured or distributed by Alltrade, and does not apply to products
and/or components thereof designed, manufactured and/or assembled by others,
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.
THERE ARE NO WARRANTIES
for which Alltrade makes no warranties whatsoever.
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
Warranty Performance
This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion
to determine whether any item or part is nonconforming and, if so, whether the
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
19
20
Warranty Disclaimers
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
Limitations on Warranty Disclaimers
Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department toll free at 1-800-590-3723 for general repair information and charges.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
21
22
|